 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| AC-DC 500-600 Watts SMC/SMD Series * * * * * * * High Peak Load Rating xppower.com Single Outputs from 3.3 V to 54 V Active PFC Remote On/Off Optional Current Share SEMI F47 Compliant Optional Constant Current Limit Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor Earth Leakage Current Input Protection * * * * * * * 90-264 VAC (120-370 VDC) 47-63 Hz 9 A at 90 VAC, 3.5 A at 230 VAC 40 A at 230 VAC 0.99 typical <2.4 mA max at 264 VAC Fitted with a T10 A/250 V fuse General Efficiency Isolation Switching Frequency Power Density Signals Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Over/Undershoot Transient Response Ripple & Noise Overvoltage Protection Overtemperature Protection Overload Protection Short Circuit Protection Remote Sense Remote On/Off Current Share * * * * * * * * * * * * * * * * * * * See tables 5% minimum 1% No minimum load required 1.5 s at 230 VAC, 2.5 s at 110 VAC 40 ms typical 18 ms max at 120 VAC 0.5%, low line to high line 1%, 1-100% of load (see note 4) 5% max 5% max deviation, 500 s recovery to within 1% for a 50% load change See table 110-130% recycle input to reset >85 C ambient with auto recovery (measured internally) 110% to 135% with auto recovery Trip and restart (Hiccup mode) Compensates for up to 0.5 V line drop On = TTL Logic HIGH, or open circuit Off = TTL Logic LOW or short circuit Optional single wire current share within 10% for up to 4 units Current Monitor MTBF * 80% min at 230 VAC, 70% min for Vo 5V * 3000 VAC Input to Output, 1500 VAC Input to Ground, 250 VDC Output to Ground * 100 kHz PFC, 25 kHz PWM * 6.93 W/In3 * Green LED for Power On, Power Good TTL HIGH within 100-500 ms and LOW 1 ms before loss of regulation * 0.5 V to 3 V output voltage denoting 0-100% output current * 100 kHrs min per MIL-HDBK-217F Environmental Operating Temperature * 0 C to +70 C, derate from 100% load at +50 C to 50% load at +70 C Cooling * 30 CFM for SMD U-channel versions Operating Humidity * 5-90%, non-condensing Storage Temperature * -20 C to +85 C Operating Altitude * 3000 m Shock * 15 g (non-operation), 11 ms (half sine wave), 3 times for each axis Vibration * 10-55 Hz (non-operation) 2 g, sweep time 3 mins, 60 mins/axis EMC & Safety Emissions Harmonic Currents ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Safety Approvals * FCC Part 15 & CISPR 22 Class B conducted * EN61000-3-2, EN61000-3-3 * EN61000-4-2, level 3 Perf Criteria A * EN61000-4-3, 3 V/m Perf Criteria A * EN61000-4-4, level 2 Perf Criteria A * EN61000-4-5, level 3 Perf Criteria A * EN61000-4-6, 3V Perf Criteria A * UL60950, CSA C22.2 No. 950, EN60950, CE Mark LVD, SEMI F47 Compliant (high line only) at 100% rated power output AC-DC Models and Ratings Output Power 264 W 400 W Output Voltage(3,4) Preset Range 3.3 V 2.0-3.3 V 5.0 V 5.0-6.0 V 12.0 V 12.0-15.0 V 15.0 V 12.0-15.0 V 18.0 V 16.0-21.0 V 24.0 V 22.0-30.0 V 27.0 V 22.0-30.0 V 36.0 V 31.0-47.0 V 48.0 V 48.0-56.0 V 54.0 V 48.0-56.0 V 3.3 V 2.0-3.3 V 5.0 V 5.0-6.0 V 12.0 V 12.0-15.0 V 15.0 V 12.0-15.0 V 18.0 V 16.0-21.0 V 24.0 V 22.0-30.0 V 27.0 V 22.0-30.0 V 36.0 V 31.0-47.0 V 48.0 V 48.0-56.0 V 54.0 V 48.0-56.0 V SMC/SMD Series Output Current Maximum Peak(1) 80.00 A 120.00 A 80.00 A 120.00 A 41.67 A 75.00 A 31.00 A 56.00 A 27.78 A 50.00 A 20.83 A 37.50 A 18.50 A 33.33 A 13.89 A 25.00 A 10.42 A 18.75 A 9.25 A 16.67 A 90.00 A 135.00 A 90.00 A 135.00 A 50.00 A 75.00 A 40.00 A 56.00 A 33.00 A 50.00 A 25.00 A 37.50 A 22.22 A 33.33 A 16.67 A 25.00 A 12.50 A 18.75 A 11.10 A 16.67 A Ripple & Noise(2) 75 mV 75 mV 120 mV 150 mV 180 mV 240 mV 270 mV 360 mV 480 mV 540 mV 100 mV 100 mV 120 mV 150 mV 180 mV 240 mV 270 mV 360 mV 480 mV 540 mV Model Number SMC500PS03-C SMC500PS05-C^ SMC500PS12-C^ SMC500PS15-C^ SMC500PS18-C SMC500PS24-C^ SMC500PS27-C SMC500PS36-C SMC500PS48-C^ SMC500PS54-C SMC600PS03-C SMC600PS05-C^ SMC600PS12-C^ SMC600PS15-C^ SMC600PS18-C SMC600PS24-C^ SMC600PS27-C SMC600PS36-C SMC600PS48-C^ SMC600PS54-C 500 W 297 W 450 W 600 W Notes 1. This peak can be taken for 500 s only, average power should not exceed the maximum power. 2. Ripple & Noise is measured using 0.1 F ceramic and 22 F electrolytic capacitor, 20 MHz bandwidth. 3. Alternative output voltages available, consult sales. 4. Load regulation increases to 2% for 0-100% load change. 5. For output currents >50 A, please connect remote sense to meet regulation ratings. Available from Farnell. See pages 204-206. ^ Available from Newark. See pages 207-208. Options * * * * * For U-channel version replace `SMC' in the part number with `SMD' and remove `-C' e.g. SMD600PS12 (See Derating Curve Note 1.) Constant current limit (95-100%) add suffix `-B' (not available on 3.3 V or 5.0 V models) Current share and internal oring diode add suffix `-I' to model number. Optional IEC320 inlet replace suffix `-C' with `-D'. Not available for SMD models. For multiple option codes please place optional codes in alphabetical order. e.g. SMC500PS12-BD. Derating Curve 100 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 Ambient Temperature (C) 60 70 80 Notes 1. SMD units require 30 CFM forced air cooling. Load (%) AC-DC Mechanical Details SMC with integral fan All dimensions are in inches (mm) Weight: 3.30 lbs (1.5 kg) approx. A B B A SMC/SMD Series 2.00 (50.8) 2.50 (63.5) 2.09 (53.0) 5.00 (127.0) 1.59 (40.4) CN3 Pin 7 FAN 2.50 (63.5) 2.50 (63.5) 1.59 (40.3) 6.00 (152.4) Pin 1 2.50 (63.5) A B 1.75 (44.45) B 1.62 0.32 (8.25) (41.25) A 1.25 (31.9) 2.50 (63.6) A B 0.59 (15.0) VOVO+ 4.25 (108.0) B A LN 0.88 (22.25) IEC320 or equivalent `-D' Option Terminal Block M3 Screw 3 Pins 8.25 mm center 9.17 (233.0) Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center B Mounting Hole 8 Places A Mounting Hole 8 Places A B B A 2.00 (50.8) 2.50 (63.5) 0.22 (5.6) 0.25 (6.4) 0.22 (5.6) 0.25 (6.4) UNC6-32 (Zn-plated) 9.17 (233.0) M4 (Zn (yellow) -plated) Pin 1 2(3) 3 4 5 6(3) 7(3) CN3 (Signals) Function Current monitor Current share Return Power good Remote On/Off -Remote sense +Remote sense 0.07 (1.9) 0.02 (0.6) SMD U-Channel All dimensions are in inches (mm) Weight: 3.09 lbs (1.4 kg) approx. 2.00 (50.8) A B B A 2.50 (63.5) 0.07 (1.9) 0.02 (0.6) 1.50 (38.1) 1.00 (25.4) 5.00 (127.0) 1.00 (25.4) CN3 Pin 7 2.50 (63.5) 6.00 (152.4) FAN 2.50 (63.5) Pin 1 A Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center B 0.92 (23.25) 1.29 (32.78) A B VO- 1.75 (44.45) 2.50 (63.5) A B 4.33 (110.0) 0.37 (9.5) 0.37 (9.5) A 1.29 (32.78) 0.92 (23.25) 8.00 (203.20) VO+ Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center NL A B Recommended Air Flow B B A 2.00 (50.8) 2.50 (63.5) Pin 1 2(3) 3 4 5 6(3) 7(3) CN3 (Signals) Function Current monitor Current share Return Power good Remote On/Off -Remote sense +Remote sense Notes 1. 2. 3. 4. Logic connector CN3 mates with JST XHP-7 or equivalent and JST SXH-002T-P0.6 crimp terminals. Fan connector mates with JST XHP-2 or equivalent and JST SXH-002T-P0.6 crimp terminals. Output is 12 VDC/160 mA Current share only available on `-I' models, remote sense not available on `-I' models. Current share not available with constant current models. Maximum mounting screw penetration: 0.15 (4.00) from case outer surfaces. AC-DC Application Notes Remote Sense SMC/SMD Series Supply 1 Output Return CL CN3 Pin 2 Current Share Output V1 + CD Comm LOAD Supply 2 Supply CN3 Pin Output 7 Sense + - + Twisted Pair LOAD CL Return CN3 Pin 6 Sense CN3 Pin 2 Current Share CD Output Note: 1. CL is 47 F electrolytic capacitor. 2. CD is 0.1 F ceramic capacitor. Output + CD Supply 1 + Twisted Pair LOAD CL Remote On/Off CN3 Pin 7 Sense + - Supply CN3 Pin 6 Sense CD CN3 Pin 2 Curr Supply 2 ON POWER GOOD Output CN3 +5 V Pin 5, control connector ON/OFF PSU 1K POWER NOT GOOD CN3 Pin 2 Curr Note: POWER GOOD 1. Applying <0.3 V or short between CN3 Pin 3, controlCN3 Pin 4, control connector connector pins 5 and 3 turns the output OFF. OFF Return DC OK 2. Applying >4.5 V or open circuit between pins 5 and 3 turns output ON. CN3 Pin 3, control connector Return PS Power Good POWER NOT GOOD +5 V FAN OK 1K +5 V 1 FAN FAILED POWER GOOD CN3 Pin 4, control connector DC K OK FAN OK PSU CN1 Pin 1, control connector CN3 Pin 3, controlFan Fail connector POWER NOT GOOD Return Parallel Connection with Current Share Option CN1 Pin 2, control connector Return FAN FAILED +5 V Supply 1 1K CL Output Return CN1 Pin 1, control connector CN3 Pin 2 Current Fan Fail Share FAN OK V1 LOAD Comm Supply 2 Output 2, control connector CN1 Pin Return Return FAN FAILED CN3 Pin 2 Current Share 14-Jan-08 |
Price & Availability of SMC500PS03-C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |